The 2" to 1" frangible coupling includes a 1" column with additional set screw for secure installation using aviation accessories. The 2" to 1" frangible coupling adapts to the 1.5" Floor Flange, the 2" Floor Flange, the 601 airport mounting plate and conventional 2" threaded NPT stakes. The 2" to 1" frangible coupling is manufactured out of aluminum, providing FAA compliance for high and medium intensity edge light requirements. The 2 " NPT Frangible Coupling will provide a permanent, temporary or expedited mounting system for aviation lights.

The 2" to 1" frangible coupling includes a 1" column with additional set screw for secure installation using aviation accessories. The 2" to 1" frangible coupling adapts to the 1.5" Floor Flange, the 2" Floor Flange, the 601 airport mounting plate and conventional 2" threaded NPT stakes. The 2" to 1" frangible coupling is manufactured out of aluminum, providing FAA compliance for high and medium intensity edge light requirements. The 2 " NPT Frangible Coupling will provide a permanent, temporary or expedited mounting system for aviation lights.

The 2.0" floor flange is designed for concrete installations using the 2" to 1" frangible coupling for taxiway, runway, threshold, apron, or helipad edge installations. The 2.0" floor flange is excellent for permanent installations where current infrastructure is not in place and edge lights need to be secured and frangible.

The 1.5" floor flange is designed for concrete installations using the 1.5" frangible coupling for taxiway, runway, threshold, apron, or helipad edge installations. The 1.5" floor flange is excellent for permanent installations where current infrastructure is not in place and edge lights need to be secured and frangible.

The A601 Stake Mounting System is a complete mounting system for Model A601 solar-powered LED airfield lights that are installed in gravel or earth locations. The system includes a 14-inch (35cm) mounting stake that can be hammered into the ground, a frangible grooved column that can be replaced separately if broken on impact (as designed) and a mounting base pre-drilled to accommodate the A601 light. The system comes optionally, with a 10-inch (25cm) diameter grass guard disk that keeps grass and weeds from growing around the mounting stake (Part # AW1601GG).

The Stake Tapper is a recommended accessory for the installation of the A601 Stake Mounting Kit. Made from stainless steel, the unit is placed inside the circular mount at the top of the mounting stake. The Stake Tapper is designed to take the force of a hammer or mallet when installing the A601 stake mounting stake into a dirt, sand or gravel environment. The tapper protects the circular mounting hole for the frangible grooved column so it is not deformed during installation.

The A601 Fence Mounting Kit is designed for installing A601 aviation lights on standard chain link fences with a circular top bar along the top of the chain link fence. The kit features two U-bolts, a mounting plate, and all the required hardware to securely affix A601 lights to most fences.

Manufactured out of galvanized steel, the all weather airport mounting stake allows for permanent installation in earth and gravel environments at general aviation airports and remote defense airfields. The 30" airport mounting stake is available in 2" and 1.5" coupling configurations. Frangible coupling size must be determined before ordering. Stake (Angle Iron) Mounting Instructions: Install the stake in a 6" (15 cm) diameter hole at a depth of 30" (76 cm). Do not install stake by driving it into the ground. Backfill around the stake with thoroughly compacted earth passing a 1" (2.54 cm) sieve. Where required due to unstable soil conditions, backfill with concrete. Install the top of the stake even with, or not more than 1/2" (1.3 cm), above the finished grade and maintain within 1 degree of the vertical. In areas where frost may cause heaving, anchor the stake with concrete and use a permeable backfill material such as sand and then cover the top surface with an impervious material to reduce moisture penetration.

Manufactured out of galvanized steel, the all weather airport mounting stake allows for permanent installation in earth and gravel environments at general aviation airports and remote defense airfields. The 30" airport mounting stake is available in 2" and 1.5" coupling configurations. Frangible coupling size must be determined before ordering. Stake (Angle Iron) Mounting Instructions: Install the stake in a 6" (15 cm) diameter hole at a depth of 30" (76 cm). Do not install stake by driving it into the ground. Backfill around the stake with thoroughly compacted earth passing a 1" (2.54 cm) sieve. Where required due to unstable soil conditions, backfill with concrete. Install the top of the stake even with, or not more than 1/2" (1.3 cm), above the finished grade and maintain within 1 degree of the vertical. In areas where frost may cause heaving, anchor the stake with concrete and use a permeable backfill material such as sand and then cover the top surface with an impervious material to reduce moisture penetration.

Optional infrared programmer. Functions available through the programmer include: Flash code settings Intensity and autonomy adjustments LUX Level adjustments for the photoelectric switch that automatically turns the on/off at dusk/dawn Activation / deactivation ability for storage or transport A battery voltage check to determine the relative health of the battery system About the infrared programmer The programmer employed to control its Model A601 and A702 aviation lights is a standard infrared unit, identical to those used to operate televisions, VCR's, stereos, etc. Why use a standard infrared programmer? There are many reasons behind this decision: Infrared technology requires minimal additional power to work effectively -- an important quality for our solar-powered, self-contained products. The programmer is simple to use and people are typically familiar with its operation. The programmer is extremely cost-effective. These programmers are mass-produced and the cost is very low relative to the cost of supplying a programmer .

Combat vandalism and theft by using our stainless steel security bolt system. Once secured using our tamper-resistant, ultra-hard Chromium-Vanadium security fasteners, lights are extremely difficult to remove. Each security bolt system requires a unique, perfectly cut key to operate. Each kit contains two security bolts and two security nuts. The driver and key for the secure nut and bolt are purchased separately.

The 601 Bolt Kit contains the required hardware to mount 601 lights to the 601 mounting plate. Each package contains the necessary items to properly mount one light. Parts list includes:

• Nut, lock, ¼"-20, SS (3)
• Washer, flat, 1/4", SS (9)
• 1/4"-20 x 1 1/2", hex cap screw, SS (3)

The bird deterrent accessory attaches easily to any Model 601 or 700 Series light. The spikes on the deterrent discourage birds from perching on the light.