The 2.0" floor flange is designed for concrete installations using the 2" to 1" frangible coupling for taxiway, runway, threshold, apron, or helipad edge installations. The 2.0" floor flange is excellent for permanent installations where current infrastructure is not in place and edge lights need to be secured and frangible.

Manufactured out of galvanized steel, the all weather airport mounting stake allows for permanent installation in earth and gravel environments at general aviation airports and remote defense airfields. The 30" airport mounting stake is available in 2" and 1.5" coupling configurations. Frangible coupling size must be determined before ordering. Stake (Angle Iron) Mounting Instructions: Install the stake in a 6" (15 cm) diameter hole at a depth of 30" (76 cm). Do not install stake by driving it into the ground. Backfill around the stake with thoroughly compacted earth passing a 1" (2.54 cm) sieve. Where required due to unstable soil conditions, backfill with concrete. Install the top of the stake even with, or not more than 1/2" (1.3 cm), above the finished grade and maintain within 1 degree of the vertical. In areas where frost may cause heaving, anchor the stake with concrete and use a permeable backfill material such as sand and then cover the top surface with an impervious material to reduce moisture penetration.

Manufactured out of galvanized steel, the all weather airport mounting stake allows for permanent installation in earth and gravel environments at general aviation airports and remote defense airfields. The 30" airport mounting stake is available in 2" and 1.5" coupling configurations. Frangible coupling size must be determined before ordering. Stake (Angle Iron) Mounting Instructions: Install the stake in a 6" (15 cm) diameter hole at a depth of 30" (76 cm). Do not install stake by driving it into the ground. Backfill around the stake with thoroughly compacted earth passing a 1" (2.54 cm) sieve. Where required due to unstable soil conditions, backfill with concrete. Install the top of the stake even with, or not more than 1/2" (1.3 cm), above the finished grade and maintain within 1 degree of the vertical. In areas where frost may cause heaving, anchor the stake with concrete and use a permeable backfill material such as sand and then cover the top surface with an impervious material to reduce moisture penetration.

The airport 700 Series mounting plate is designed for elevated runway, threshold and runway caution edge lighting. The 700 Series mounting plate is designed for stake mounted or floor flange installations on concrete and/or dirt surfaces. Manufactured to fit 1.5" or 2" to 1" frangible couplings, the 700 Series mounting plate is designed to bolt into the bottom of the 700 series aviation light using stainless steel bolts. Powder coated aviation yellow, the 700 Series mounting plate adapts to the 1.5" Floor Flange using a 1.5" frangible coupling or the 2" Floor Flange using a 2" to 1" frangible coupling. Common size of the airports coupling will determine which floor flange is ordered.

The 700 Series Bolt Kit contains the required hardware to mount 700 series lights to the correct mounting bases. Each package contains the necessary items to properly mount one light. Parts list includes: Flat washer, ½", SS (8) Screw, cap, hex, ½"-13, SS (4) Nut, lock, ½"-13, SS (4)

The airport wedge anchor bolt is designed for securing the 1.5" or 2" Floor Flange to hardened concrete and dirt surfaces. Four 3/8" X 3 ¾" wedge anchor bolts are used in installations on permanent, temporary and expedited airfields. Combined with the 1.5" or 2" Floor Flange, these wedge anchor bolts are ideal for permanent installations where current infrastructure is not in place and edge lights need to be secured and frangible.

New centralized, handheld wireless control unit, including antenna, is a secure 900 MHz radio transceiver. With a control range of up to 2.5 miles and utilizing a secure RF signal, the wireless controller reliably communicates and controls any number of ’s A704-5 solar-powered LED airfield lights from the ground, control tower or air.

The bird deterrent accessory attaches easily to any Model 601 or 700 Series light. The spikes on the deterrent discourage birds from perching on the light.